The RANGER C300 sliding gate motor is designed for users wishing to motorize their sliding gate to automate its opening and closing. It allows you to transform your gate into an electric sliding gate. This rack-and-pinion motor is suitable for all types of sliding gates that can be motorized. Whether for a PVC, wood, aluminum, or iron sliding gate, this automatic system can be installed on all models weighing less than 300 kg.
Here are the main technical specifications of the motor:
Motor voltage: 230V – 250W Input power: 220VAC±10%/110VAC±10% Frequency: 50Hz/60Hz Gear module: M4 Z=16 teeth Output torque: 30.0 Nm Nominal rotation speed: 14,000 rpm Maximum gate weight: 300kg on level ground Magnetic start and end stops Environmental temperature: -25°C ~ +55°C Protection class: IP55 Opening speed: approximately 12 meters per minute Maximum force: 1100N Nylon rack Control card included with the motor.
Accessories included:
- Two 4-button remote controls with protective cover. Batteries are included. - Nylon rack (4m – 12 pieces of 33cm) - Installation and setup manual - Two quick release keys in case of power outage
The motor cannot be connected to a backup battery. In the event of a power outage, manual unlocking with two keys is possible. This disengages the motor's output pinion and allows you to operate your gate freely. The flashing light and photocells are not included.
RANGER C300 motor features:
- Opening according to your choice: left to right (factory mode) or right to left. - Automatic closing: after opening, the gate will automatically close after 0, 10, 30, or 60 seconds, depending on your choice. - Pedestrian mode: the gate opens only partially and then closes within 0, 5, 10, or 30 seconds. - Condominium mode: this mode allows you to reduce settings and configure up to 50 remote controls. Each remote control will control: button 1 (gate opening), button 2 (gate stopping), button 3 (gate closing), and button 4 (pedestrian mode). Each remote control will operate in the same way. - Adjustable opening and closing sensitivity: you can adjust the opening and closing force depending on your environment. - Manual gate unlocking. Using the provided key, you can disengage the opening of your gate and operate it manually. - Auto-stop. The gate stops if it encounters an obstacle.
You can combine this motor with photocells, a flashing light, and an opening push button. Be sure to check the electrical compatibility (voltage in volts) of your existing accessories if they are not from our website. All our accessories are compatible with all our motors.
Installation Tips:
To successfully connect and configure your motor, proceed step by step and check that it's working properly between each step. If you're adding accessories to your C300 motor, check that your motor is working properly each time. Finally, make sure your electrical wiring is clean. This will help you operate your system and prevent electrical leaks. Our Casanoov technical team is here to assist you if needed.
The FLASH traffic light connects to your swing or sliding gate operator to indicate the opening and closing of your automatic gate.
Information and technical data : - Bulb: LED - Operating voltage 12-265 VAC/DC - Loading capacity < 3 W - Flashing frequency 1 HZ - Operating temperature -20°C ~ +60°C - IP level IP54
The remote control is compatible for all swing gate and sliding gate operators. Resists interference. Frequency 433.92 MHz. The black cover can be slid out. It makes it possible to hide the remote control buttons and prevent them from being pressed inadvertently. Waterproof case. 12 V battery. Operating temperature : -20° - +60°. Dimensions: 54.5 mm X 30 mm X 13 mm.
Electrical compatibility is: AC/DC 12-24V Operating power is between 30mA and 50mA The Max output power. 1A at 24V DC Operating distance between infrared photocells: - 50 cm (0.5 meter) minimum. - 12 meters maximum - The minimum fixing height from the ground must be greater than 20cm. - Wall fixing screws are not included with the product
The XXL infrared lens and its electronic card can be adjusted from 0 to 90°. The fit gives you more flexibility in your setup. However, please respect a perfect horizontal alignment so that the powerful infrared can be emitted and received between the two photocells. Operating temperature: from -20°C to approx. +70°C Water protection: IP45 Recommended wiring is minimum 0.5mm² Dimension : - Total height of each photocell: approx. 96mm - Total thickness of each photocell: approx. 43mm
Casanoov photocells are compatible with all our motorizations. Casanoov photocells are compatible with all other motorizations provided that the operating voltage is respected and that your motorization for swinging or sliding gates has a connection port designed to receive a pair of infrared photocells. Find more information in our visuals, technical data sheets, technical diagrams and instructions in free access on this page.
Assembly instructions - STW-000025
